| 型號： | - |
|---|---|
| 品牌： | 安科瑞 |
| 原產地： | 中國 |
| 類別： | 電子、電力 / 電池、蓄電池、充電器 |
| 標籤︰ | 16串BMS , 主動均衡BMS , 鋰電池BMS |
| 單價： |
-
|
| 最少訂量： | 1 件 |
| 最後上線︰2016/04/15 |
APHEV-BMS-01-16-01
1 Introduction
The BMS module of 16 series adopts high precision analog front-end chip and
high performance 32 bits MCU, superior performance to extend battery life, and
ensure the batteries for safety.
2 Composition of System
Main features: high precision signal acquisition module，high precision SOC
estimation module, active energy transfer balance mode，the cell information
storage module, the cell protection module (overcharge protection, over
discharge protection, high and low temperature of cell protection), optional
LCD display module.
3 Package Information
The package is labeled with five descriptors
4 Features
4.1 Active balancing energy transfer type, high current is 1.5 A.
4.2 Optional battery balance modes: Automatic balance or Force balance.
4.3 Module reserved RS485 bus interface can be scaled to 32 cell, 48 cell and more
than thousands of cells.
4.4 Include a 4G SD card, can store 10 years for battery information.
|
Item |
Parameter |
|
Size |
210*120*37.5mm |
|
Application |
16 cells LiFePO4 batteries or 16 cells
Lithium polymer batteries |
|
Working Range |
36 – 60V |
|
Sleep mode power current |
< 3mA |
|
Normal Operating current |
< 20mA |
|
Monomer battery voltage measurement error |
< 0.002 V |
|
Monomer battery balanced current(Active
balancing energy transfer mode) |
≥1.2A Nominal 1.5 A |
|
Temperature measurement error |
±2°C |
|
Monomer battery over voltage protection |
3.55V |
|
Monomer battery low voltage protection |
2.75V |
|
Batteries over temperature protection |
65℃±2℃ |
|
Batteries low temperature protection |
≤3℃ |
|
Batteries low-voltage protection |
36±2 V |
|
Low voltage protection after the recovery
voltage |
42±2V |
|
SOC measurement error |
≤5% |
|
Battery information storage |
＞10years |
|
|
Monitoring |
3.2 inch touch screen LCD |
|
Communication |
CAN 2.0 |
|
Extension |
RS485 extension other modules |
|
Force Balance Mode
Balancing switch to position “I”. |
Balance when High - Low difference is
above 10mV. Stop balancing when the delta
is 10mV |
|
Automatic Balance Mode
(Default) switch position “0” |
(i) Balancing is always on: Monomer battery
differences over 60 mV starts automatic
balancing to 60mV.
(ii) Balance every 15 days, Balance when
High - Low difference over 60mV. Stop
balancing when the delta is 10mV or Day
15+1 |
|
BMS Module circuit protection |
Balancing modes will be turned off when the
module temperature reaches 65°C,
Balancing will restart when the temperature
is below 45°C |
|
Single cell drops below 2. 75V |
Red LED flashes and suspends discharging |
|
Single cell exceeds 3.55V |
Red LED flashes and suspends charging |
|
Battery Temperature > 70°C |
Red LED flashes and suspends discharging
and charging |
|
6 Schematic Diagram and Definition of BMS Module
Interface
6.1 Front panel interface
6.2 Anderson connection Interface.
Reset Restart measuring functions
3.2 inch LCD display module key
Reset Re-start the display, re-calibrate touch screen
|
Interface diagram |
|||
|
BMS16 front panel（look from the outlet end）
Note : P1 and P2 are configured as described in the table below |
|||
|
Pin
Number |
Function |
Pin
Number |
Function |
|
1 |
BAT-1－ |
11 |
18B20 1VDD |
|
2 |
BAT-2－ |
12 |
DQ |
|
3 |
BAT-3－ |
13 |
GND |
|
4 |
BAT-4－ |
14 |
18B20 2VDD |
|
5 |
BAT-5－ |
15 |
DQ |
|
6 |
BAT-6－ |
15 |
DQ |
|
7 |
BAT-7－ |
16 |
GND |
|
8 |
BAT-8－ |
|
－: Cell negative pole |
|
|
BMS Display Monitor - The definition of CAN BUS and 5V power supply |
|
|
|
|
|
Pin Number |
Function |
|
1 |
5V |
|
2 |
CANH |
|
3 |
CANL |
|
4 |
GND |
|
9 |
BAT-8＋ |
NOTE |
＋: Cell positive pole |
|
10 |
NONE |
|
BMS Control Interface |
|
|
BMS16 front panel（view from the outlet） |
|
|
Pin Number |
Function |
|
1 |
Over discharge protection(relay disconnected normally, contact
closure condition: 0.5A/24V) |
|
2 |
Detect input current（input: 0-5V, range: 0-150A） |
|
3 |
Over discharge protection（relay disconnected normally, contact
closure condition: 0.5A/24V） |
|
4 |
GND |
|
5 |
GND |
|
6 |
GND |
|
7 |
Detect output current（input: 0-5V, range: 0-30A） |
|
SD Card Data recording |
|
|
|
|
