1. Product Introduction
Tripod turnstile is generally used in simple dissuasion level access control of public passages. It is widely used in work attendance checking systems of factories, consumption systems of public institutions, access control of residential estates, ticket exit systems of scenic sports and other arenas, handkey management systems of construction sites (in Hong Kong, Macao) and so on. The mechanical part of the turnstile contains an emergency control device, which allows automatic dropping of the tripod bar in the level position in case of power fail; when power supply is resumed, manual reset of the tripod bar is required. The turnstile has different optional configurations for the applications of all building conditions and for the control of all kinds of passage entrance-exits. Different identification systems (ID card, IC card, barcode, handkey, fingerprint, iris, etc.) can be configured into the turnstile system. The turnstile can be connected to any kinds of controllers and various consumption devices.
2. Features and Functions
1) The turnstile has fully rainproof stainless steel housing, processed by numeric control punching and laser drilling, novel and elegant.
2) The turnstile has unique mounting surfaces (for the installation of card reader and indicator light, etc.), ensuring simple and convenient installation of the turnstile control equipment of system integrators.
3) The interior module of the tripod turnstile has a cushioning device for automatic regulation of hydraulic pressure, which helps to realize low noise, no impact and automatic decelerated returning to home position during operation of the turnstile. The finish of the interior module has been treated by yellow dichromate plating.
4) Programmable turnstile control is available, for one-direction or bi-direction control (to be set by the user).
5) The base cover can be opened using a key, therefore it is convenient for the user to install it. There are card reader supports at both sides of the turnstile, and a 40CM*18CM mounting plate, for the mounting of controller, is fixed at one side of the housing.
6) The base is fixed with four 10MM expansion bolts.
3. Technical Parameters and Configuration:
Housing: L (1200 mm)* W (280 mm) * H (98mm); Tripod Bar: Length 480 mm, Diameter 40 mm
Power Supply: Single-Phase AC220V, 3A, 50/60Hz
Control Voltage: DC24V, Power Consumption: 40W
Electromagnetism: No Residual Magnetism, without Magnetization
Buffer: Hydraulic Pressure Reset Cushioning, without Bumping Noise
Operating Ambient Temperature Range: -20℃~60℃
Operating Ambient Humidity Range: 0~95%RH
Net Weight: 80kg
Gross Weight: 90kg
Standard Configuration:
Stainless Steel Housing: 1 PC (With Supports for Mounting the Controller and Card Reader)
Bi-direction Electric Controlled Tripod Turnstile Interior Module: 1 PC
AC220V/DC24V Output Power Supply: 1 PC
Control Interface Board: 1 PC (Model: jzh-03)
Bi-direction Electronic Indicating Light: 1 PC
Instructions Manual: 1 PC
4. Control Interface
Two-Way (PASS1.PASS2) dry contact (or level) control signal input for controlling electromagnets and legal signal indicating lights at the in and out direction
Two-Way (FAL1, FAL2) dry contact (or level) status input for the control of illegal signal indicating light
Two-Way DC12V (DOOR1, DOOR2) legal connection, for connecting any kinds of controllers and various consumption devices
5. Turnstile Interior Module
1) The turnstile mechanical interior module is for manual dropping of the tripod bar after the control of the turnstile is released; After a passenger passes the turnstile, another bar of the tripod stays at the level position after it passes the hydraulic pressure cushioning device of the interior module. Then, another passenger can only be released (passing the turnstile) after the control of the turnstile is released again. Pushing of the bar only requires 0.5Kg force.
2) The interior module of the electronic turnstile consists of three parts:
a) Mechanical Part: (The mechanical structure has been installed and tested to be acceptable before it is delivered, so the user does not need to adjust it.)
b) Electrical Part:
Open-close Electromagnet: DC24V power supply, one piece of electromagnet at each of the left and right side. (For Two directions). For unidirectional usage, only connect the power supply at one side.
Bar Dropping Electromagnet: DC24V power supply; It is in pickup position during power supply, and it is in dropout position during power fail therefore allows dropping of bar. (The position of the electromagnet can be adjusted.)
Micro-active Switch: (Travel Switch) When one bar of the tripod turns 120 degrees, the micro-active switch will transmit the reset signal to the control board, and then the control board sends instructions to reset the turnstile. (One passenger passes)
c) Cushioning Device: An oil buffer (Model: AD1410-5) made in Taiwan is used. The buffer can be used to adjust and control the reset speed of the tripod bar. When the tripod turns too quickly and there is bumping noise, change the value of it from small to large (0-8) until sound result is obtained. The turnstile has been adjusted and tested to be acceptable before it is delivered. After it is used for a certain period and somewhat large bumping noise is heard, you can adjust the buffer appropriately.
